How to Chip a Golf Ball: 3 Setup Fixes for Clean Contact
Last updated: November 17, 2026
Piece: Short game | Level: Break 100 | 5-minute read | Part of the Path 2 Par blueprint
To chip cleanly, set the ball just back of center, lean about 60 to 70 percent of your weight on your lead foot, and keep your hands slightly ahead of the ball. Rock your shoulders back and through without flicking your wrists, and brush the grass. Pick a landing spot on the green and let the ball roll the rest of the way to the hole.
The leak: chunked and bladed chips
A chunked chip digs into the ground behind the ball and goes a few feet. A bladed chip hits the middle of the ball and races across the green. Both usually come from the same habit: trying to lift the ball into the air with a flick of the wrists. A chip is a low shot where the club’s loft does the lifting.
The fix: three steps
- Set up for a downward brush. Stand with your feet close together and your stance slightly open. Play the ball just back of the middle, put about 60 to 70 percent of your weight on your lead foot, and keep your hands slightly ahead of the ball.
- Rock your shoulders. Keep your wrists quiet and swing back and through by rocking your shoulders, like a putting stroke. Your chest and the club move together.
- Pick a landing spot. Choose a spot on the green a couple of paces from the edge and aim to land the ball there. Choose a less lofted club, like an 8-iron, when you want more roll, and a wedge when you want it to stop sooner.
Not sure whether to chip or pitch? See Chip vs. Pitch Shots: Technique, Club Selection, and a Drill.
The drill: the towel landing spot
Lay a towel on the green a couple of paces from the edge. Chip ten balls from the fringe or short grass with a pitching wedge or 9-iron and try to land each one on the towel. Success: at least 7 of 10 balls land on the towel.
Your 7-day game plan
- Day 1: practice the setup in front of a mirror: ball back of center, weight forward, hands ahead.
- Day 2: make 20 shoulder-rocking swings with no ball and brush the grass.
- Day 3: run the towel drill with a pitching wedge.
- Day 4: run the towel drill with an 8-iron and note how far it rolls.
- Day 5: chip ten balls to a single hole and note which club left you closest.
- Day 6: play nine holes and pick a landing spot for every chip.
- Day 7: count how many chips finished within a club length of the hole.
Your rule for the next round
Pick a landing spot for every chip, set your weight forward, and brush the grass.
The measure
Count how many of your chips per round finish within a club length of the hole. Record a baseline over two rounds, then aim to add one or two per round within four weeks. That is a target, not a guarantee.
Next piece on the path
Decide between chip and pitch with Chip vs. Pitch Shots, then learn the shot that gets you out of sand with How to Hit Out of a Greenside Bunker, and build the rest of your touch with Short Game: 6 Things to Practice to Save Strokes. See the full Path 2 Par blueprint.
Common questions
How do you chip a golf ball?
Set the ball just back of center with your weight forward and hands slightly ahead. Rock your shoulders back and through with quiet wrists, brush the grass, and aim for a landing spot on the green.
Why do I chunk my chip shots?
Usually your weight stays back and you flick your wrists to lift the ball, so the club hits the ground first. Keep your weight on your lead foot and let your shoulders move the club.
What club should I use to chip?
Any club from a 7-iron to a sand wedge can work. Less loft makes the ball fly lower and roll farther, and more loft makes it fly higher and stop sooner. Pick based on how much green you have between the ball and the hole.
Why do I blade my chips?
Most often you are trying to help the ball up, so the club rises before it meets the ball and hits the middle. Keep your hands ahead and your wrists quiet through the strike.
