How to Hit Irons Pure: A 3-Step Strike Drill

Short answer: A pure iron strike meets the ball first, then the turf, at the center of the face. Set your weight forward, shorten your swing and read your strike marks.

Last updated: November 17, 2026

Piece: Approach shots | Level: Break 80 | 5-minute read | Part of the Path 2 Par blueprint

A pure iron shot meets the ball first and the turf second, at the center of the clubface. To get there, set a little more weight on your lead foot, play the ball near the middle of your stance, and swing at three-quarter length so you can find the center. Then use impact tape or foot powder spray to see where the ball is actually hitting the face, and adjust until the marks sit in the middle.

The leak: contact that is close but not centered

Once you stop hitting big misses like fat and topped shots, the next gain is consistency. Strikes that land toward the heel or toe lose distance and send the ball offline, and you cannot see the pattern by watching ball flight alone. A mark on the clubface shows you exactly where you are hitting it.

The fix: three steps

  1. Set the low point forward. Play mid-irons near the middle of your stance and put about 55 to 60 percent of your weight on your lead foot. The club then reaches the bottom of its arc just after the ball. Check the chart in Golf Ball Position: Where to Play Every Club.
  2. Shorten the swing. Make three-quarter swings at a smooth, steady tempo. You give up a little distance, and you gain the control to find the center of the face.
  3. Read the strike. Put impact tape or a light coat of foot powder spray on the clubface, hit five balls, and look at the marks. Marks toward the heel can mean you stand too close or your weight is on your toes. Marks toward the toe can mean you stand too far away. Adjust one thing at a time and hit five more.

The drill: the strike-mark drill

Use a 7-iron and impact tape or foot powder spray. Hit ten balls at three-quarter speed, wiping or replacing the tape or spray after each shot. Note where each mark lands. Success: at least 7 of 10 marks land within about one inch of the center of the face, and your divot starts at or just after the ball.

Your 7-day game plan

  • Day 1: check your setup: ball near the middle, a little more weight on your lead foot.
  • Day 2: make 20 slow three-quarter swings and brush the grass in the same spot each time.
  • Day 3: run the strike-mark drill with a 7-iron.
  • Day 4: adjust your distance from the ball based on your marks and run the drill again.
  • Day 5: repeat the drill with a 9-iron and a 5-iron.
  • Day 6: play nine holes with a three-quarter swing on every iron shot.
  • Day 7: count the iron shots you hit solid and compare them to your first round.

Your rule for the next round

Take one more club and swing at three-quarter speed, so the center of the face does the work.

The measure

Count the iron shots per round that you would call solid. Record a baseline over two rounds, then aim to add a few per round within four weeks. That is a target, not a guarantee.

Next piece on the path

If you still hit behind the ball, read How to Stop Hitting Fat Iron Shots. Then learn your distances with How to Control Wedge Distance: The Clock Drill and build a practice session with Driving Range Practice: A 30-Minute Plan for High-Handicap Golfers. See the full Path 2 Par blueprint.

Common questions

What does it mean to hit an iron pure?

It means the clubface strikes the ball first and then the turf, at or near the center of the face. The ball flies on the line you aimed with a clean, solid feel.

Should I hit down on my irons?

Yes, with irons from the fairway you want a slightly downward strike so the ball is struck before the ground. The divot should be shallow and start at or just after the ball.

Why are my iron shots inconsistent?

Often the strike moves around the face, or the bottom of your swing moves around the ball. Use impact marks to see where you are hitting the face, and check your weight and ball position to steady the low point.

Does impact tape or foot spray work?

Both leave a mark where the ball meets the face, so you can see your strike pattern. Tape is cleaner, and foot powder spray is cheap. Wipe the face between shots so the marks stay readable.

About the author: Greg Kennedy is a golf coach and the writer behind Path 2 Par. See his PGA.Coach profile for his current credentials, course, and lesson availability, or learn more about Path 2 Par.